Global Chem Source Corp.
Toll Free
1-866-391-1126
Local (503) 391-1126
www.GlobalChemSourceCorp.com
Main Category : Concrete (Form Oils, Cleaners and Cures) / SEALER / CURES
FLO-CRETE II Concrete sealer--Exterior and Interior use
Select Item :
Price: $436.20
Qty :
 
FLO-CRETE II
Indoor / Outdoor Sealer

DESCRIPTION: This non-resilient floor sealer is an aqueous acrylic resin emulsion designed for sealing non-resilient surfaces such as concrete, terrazzo, quarry tile, slate, and other hard surfaces. This floor sealer is water based acrylic resin with outstanding durability and chemical resistance to the contact of several industrial chemicals such as acids, oils, detergents, gasoline, and caustics. This floor seal is a non-breathing solid sheet type seal, designed to resist surface spills and staining. This product can be used in garages, service stations, warehouses, manufacturing plants, food processing plants, or other areas where protection is desired.

ADVANTAGES:
 Exterior & Interior use Non-Yellowing
 Slip resistant Water-based
 Quick Drying Chemical and water resistant
 Re-coats easily


DIRECTIONS: The surface to be coated must be thoroughly cleaned. Remove all grease, oil, or soil with a heavy duty degreaser cleaner. Second application of cleaner may be needed for heavy oily areas where the stains have penetrated deep.
NOTE: ANY OIL LEFT IN PORES OF FLOOR WILL AFFECT ADHESION OF SEALER FlLM TO SUBSTRATE.
Rinse floor thoroughly with clean water. Squeegee or wet vacuum all excess water. Let floor dry a minimum of 2 hours or more if in damp weather. Many concrete floors are troweled exceptionally smooth or wear has smoothed floor and it would be advisable to give a mild acid bath. Make a 5% solution of muriatic acid. Mop onto floor and let set. When bubbling ceases, rinse floor with fresh water. Let floor dry the recommended time of a minimum of 2 hours or more. It is extremely important that the floor be completely dry. Apply this floor sealer with a string mop, lambs wool applicator, Hudson type sprayer, airless sprayer, or one of the new type floor finish applicators. Let sealer dry for 20 to 60 minutes, then apply a second coat. A third coat may be applied for a high gloss. It is recommended that a 24 hour or longer waiting period be allowed before heavy equipment usage.

NOTE: To test cleanliness of surface, place a strip of masking tape on the surface, press down then lift tape. If tape lifts easily and there is dust or grit on the adhesive side of tape, the surface is not sufficiently clean. Remove any food or food products from area during application of sealer.

CAUTION: The following may present problems. Type of floors: Quarry tile, slate, brick, Mexican tile, masonry block, exposed aggregate. Brick, Mexican tile, and masonry blocks may need additional coats because of their porous construction. (We recommend that glazed tile not be sealed with this non-resilient floor sealer.) Type of Conditions:
Sub-surface moisture and alkalineliness of surface (Note: Do not seal if surface is under 50F.) Dryness of surface-cleanliness of surface-uncovered outside exposure. It is recommended on the above flooring that a sample patch be applied and tested for 30 days before a decision is made to seal the area using a penetrating seal prior to coating with this non-resilient floor sealer.

NOTE: The information contained herein is, to the best of our knowledge and belief, accurate. We guarantee the quality of the product. Since the surface condition and product use are beyond our control, we make no guarantee of results. We assume no liability for damages or penalties resulting from following our suggestions or recommendations.
FOR INDUSTRIAL AND INSTITUTIONAL USE ONLY

SPECIFICATIONS
Slip resistance (Foot pressure) Excellent
Black mark resistance Very good
Scuff resistance Very good
Detergent resistance Excellent
Powdering resistance Excellent
Alkali resistance Very good
Acid resistance Excellent
Gasoline resistance Very good
Alcohol resistance Excellent
Hydro carbon solvent resistance Very good
Re-coating Excellent
Gloss (3 coats) Excellent
Coverage coat 1500 sq. ft./gal